Search results

Create the page "Speakers" on this wiki! See also the search results found.

• Release Note Exigo 1.3
  * Amplifiers and IP speakers with different modes can be freely mixed, but will use the best audio codec === IP speakers available in Exigo mode ===
  29 KB (4,424 words) - 09:00, 10 May 2022
• A-B System Principle
  All the areas will have speakers from both System A and System B.<br> To ensure audio coverage in an area, the speakers will be wired from both System A and System B:
  2 KB (308 words) - 12:16, 8 January 2019
• ELSIR-10C
  * Ideal for Micro Zone PA and systems that require a limited number of speakers * Ideal for speakers installed in remote locations, e.g. roads and railways
  2 KB (337 words) - 15:06, 27 April 2018
• ELSII-10H
  * Ideal for Micro Zone PA and systems that require a limited number of speakers * Ideal for speakers installed in remote locations, e.g. roads and railways
  2 KB (339 words) - 10:26, 27 April 2018
• Release Note Exigo 1.4
  ==== Volume control normalized for IP speakers and Exigo amplifiers ==== ...h volume controls will now result in the same volume reduction for both IP speakers and Exigo amplifiers
  33 KB (4,919 words) - 08:59, 10 May 2022
• Release Note Exigo 1.2
  === Tick Tone Test in Zone not Working for TKIS Kits and IP Speakers === The tick tone test was not supported for TKIS kits and IP speakers. <br>
  12 KB (1,921 words) - 09:00, 10 May 2022
• Local Mute Audio Lines
  This is typically used for muting [[:Category:IP Speakers | IP Speakers]].
  1 KB (209 words) - 15:20, 2 May 2018
• CL-135T
  5" miniature speaker for small rooms or where space for mounting speakers is limited. [[Category:Speakers]]
  556 bytes (80 words) - 15:06, 26 April 2018
• Redundancy Funtions
  ...u design the speaker layout in a given area (typically a zone) so that the speakers are managed from two different amplifiers.<br> If one of the amplifiers fails you still have audio in 50% of the speakers.
  3 KB (456 words) - 14:34, 23 October 2019
• Local Mute Control
  This function is useful in control rooms when you need to mute speakers during alarm situations. ...riority above 15 will disable the ''Local mute control'' again so that the speakers are not disconnected.
  5 KB (844 words) - 14:07, 3 January 2020
• Upgrade from 1.3.3.0 to 1.3.3.1
  ...[[Alarm Generator]] must be checked to ensure correct audio level from the speakers.
  872 bytes (124 words) - 11:44, 18 May 2018
• Recall
  ...for older PABXs where phones or intercoms are placed in many areas with PA speakers.
  2 KB (307 words) - 16:54, 12 December 2016
• ENA2200
  ...puts per channel. Each channel also has a low-power 8ohm output for single speakers. Each channel is equipped with inputs for connection to a hot-standby ampli
  12 KB (1,781 words) - 08:44, 10 April 2019
• Local Mute
  '''Local Mute''' is used when an output shall mute one or more speakers to prevent audio feedback. <br>
  3 KB (532 words) - 13:28, 18 October 2018
• ENA2400-DC
  ...puts per channel. Each channel also has a low-power 8ohm output for single speakers. Each channel is equipped with inputs for connection to a hot-standby ampli
  11 KB (1,712 words) - 08:46, 10 April 2019
• CL-200T
  [[Category:Speakers]]
  1 KB (201 words) - 15:06, 26 April 2018
• ENA2400-AC
  ...puts per channel. Each channel also has a low-power 8ohm output for single speakers. Each channel is equipped with inputs for connection to a hot-standby ampli
  11 KB (1,699 words) - 14:40, 10 April 2019
• Exigo Devices Upgrade
  * IP Speakers
  6 KB (872 words) - 10:35, 2 February 2018
• VS-IMT Upgrade
  * IP Speakers
  6 KB (940 words) - 10:51, 1 November 2019
• Upgrade TKIS-2 from version 3.0.x.x
  The [[TKIS-2]] is used as standalone and inside the IP speakers [[ELSII-10H]] and [[ELSIR-10C]].<br>
  6 KB (860 words) - 13:14, 29 May 2018

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)