|
|
| (23 intermediate revisions by the same user not shown) |
| Line 4: |
Line 4: |
| | | | |
| | This applies to the following devices: | | This applies to the following devices: |
| − | *ESC1 Controller - only the Secondary System Controller. | + | * [[ESC1]] Controller - only the Secondary System Controller |
| − | *ENA Amplifiers | + | * [[:Category:Central_Equipment|ENA Amplifiers]] |
| − | *ECPIR-P/ECPIR-3P/EAPIR-8 Access Panels. | + | * [[:Category:Indoor Access Panels|ECPIR-P/ECPIR-3P/EAPIR-8 Access Panels]] |
| − | *EAPII-1/EAPII-6 Access Panels. | + | * [[:Category:Outdoor_Access_Panels|EAPII-1/EAPII-6 Access Panels]] |
| − | *TKIS-2/TKIE-1/TKIE-2 kits. | + | * [[:Category:Kits|TKIS-2/TKIE-1/TKIE-2 kits]] |
| | | | |
| − | == Prerequisite == | + | == Upgrade Procedures == |
| | | | |
| − | The upgrade process is done by using the following tools:
| + | A complete guide on recovery with the use of VS-Turbine.ImageUpgrade application can be found [https://wiki.zenitel.com/wiki/Turbine_Stations_-_Image_recovery '''here''']. |
| − | * Standard TFTP server.
| |
| − | * Serial console to run the process.
| |
| | | | |
| − | In order to upload the firmware you need the following:
| |
| − | * USB to Serial Cable. A tutorial on how to make the cable can be found [http://exigowiki.zenitel.com/index.php?title=Turbine_to_PC_physical_connection '''here'''].
| |
| − | This cable must be used for the access panels and the kits.
| |
| − | * For the '''ESC''' Controller and '''ENA''' Amplifiers you need to use a serial cable like this:
| |
| − | [[File:Serial_cable.jpg|thumb|left|500px|Serial cable for ESC and ENA units]]
| |
| − | <br style="clear:both;" />
| |
| − |
| |
| − | * TFTP server with the prod image package. [http://tftpd32.jounin.net/tftpd32_download.html TFTP server]
| |
| − | * SSH client (serial console). [http://www.chiark.greenend.org.uk/~sgtatham/putty/ PuTTY]
| |
| − | * A prod image. This can be obtain by contacting customer support.
| |
| − |
| |
| − | == Connection ==
| |
| − | A tutorial on how to connect PC to the access panels and kits can be found '''[http://exigo.zenitel.com/index.php?title=Turbine_to_PC_physical_connection here]'''.
| |
| − |
| |
| − | You need to find the COM port for the USB cable. This can be found in the Device manager on your PC:
| |
| − |
| |
| − | [[File:USB com port.JPG|thumb|left|500px|Find the COM port in Device manager]]
| |
| − | <br style="clear:both;" />
| |
| − |
| |
| − | To connect to '''ESC''' Controller and '''ENA''' Amplifiers you must use the cable that is described above in Prerequisite.
| |
| − |
| |
| − | == Procedure ==
| |
| − | === Prepare the TFTP server on the PC ===
| |
| − | The TFTP server must be prepared with a Prod image package (f.ex. exi-prod-4.3.1.10).
| |
| − | It is important that the image is a '''Prod''' image. It is not possible to use the standard exi packages.
| |
| − |
| |
| − | On a standard TFTP server extract and store the archive to the TFTP root folder.
| |
| − |
| |
| − | === SSH connection Step-By-Step ===
| |
| − | #Connect the modified USB cable to the access panel or kit. On the '''ESC''' or the '''ENA''' you must use the described Serial cable.
| |
| − | #Connect a Ethernet cable for the new Image transfer.
| |
| − | #Start "PuTTY" (or another terminal emulator), and select:
| |
| − | ::*'''Connection type''' = Serial
| |
| − | ::*'''Serial line''': Set COM port number according to the device installation
| |
| − | ::*'''Speed''' = 115200.
| |
| − | ::*Select '''Open''' to start communication. Leave the window open.
| |
| − | [[File:Putty connection.JPG|thumb|left|500px|Putty connection]]
| |
| − | <br style="clear:both;" />
| |
| − | :4. During initial boot of the device hit '''CTRL-C''' to stop the booting process.
| |
| − |
| |
| − | === Prepare the network on the device ===
| |
| − | There are two ways of setting the network for the upgrade procedure:
| |
| − | ==== Using a DHCP server ====
| |
| − | *If you are using a DHCP server you should use these commands:
| |
| − | dhcp
| |
| − | eth0.serverip={serverip}
| |
| − |
| |
| − | ==== Using Static IP ====
| |
| − | *If you are using Static IP you should use these commands:
| |
| − | st_net_enable
| |
| − | eth0.ipaddr=10.1.11.6
| |
| − | eth0.gateway=10.1.11.1
| |
| − | eth0.netmask=255.255.255.0
| |
| − | eth0.serverip=10.1.11.2
| |
| − |
| |
| − | The IP addresses in the commands above is just an example.
| |
| − |
| |
| − | The IP setting must be done after each reset of the unit.
| |
| − |
| |
| − | You should now be ready upgrade the device.
| |
| − |
| |
| − | === Upgrade the unit ===
| |
| − |
| |
| − | :
| |
| − | ==== 1. First run these two commands: ====
| |
| − | update -t bootstream -d nand -f exi-4.3.1.10_boot
| |
| − | update -t bareboxenv -d nand -f exi-4.3.1.10_bareboxenv
| |
| − |
| |
| − | The exi package above is just an example. <br>
| |
| − | Normal package will not work. You have to use a special prod image. This can be obtain by contacting customer support.
| |
| − |
| |
| − | ==== 2. Then you have to upgrade according to the device you have: ====
| |
| − |
| |
| − | *Amplifier ENA:
| |
| − | update -t oftree -d nand -f imx28-st-ena2.dtb
| |
| − |
| |
| − | *Compact KIT:
| |
| − | update -t oftree -d nand -f imx28-st-compact.dtb
| |
| − |
| |
| − | *Extended KIT:
| |
| − | update -t oftree -d nand -f imx28-st-extended.dtb
| |
| − |
| |
| − | *Controller ESC:
| |
| − | update -t oftree -d nand -f imx28-st-esc1.dtb
| |
| − |
| |
| − | *Industrial panels EAPII:
| |
| − | update -t oftree -d nand -f imx28-st-extended-industrial.dtb
| |
| − |
| |
| − | *EX panels EAPFX:
| |
| − | update -t oftree -d nand -f imx28-st-ex.dtb
| |
| − |
| |
| − | *Alarm & Call panels ECIRP/EAPIR:
| |
| − | update -t oftree -d nand -f imx28-st-extended-exigopanel.dtb
| |
| − |
| |
| − | ==== 3. Then run these two commands: ====
| |
| − | update -t kernel -d nand -f exi-4.3.1.10_kernel
| |
| − | update -t rootfs -d nand -f exi-4.3.1.10_rootfs
| |
| − |
| |
| − | The exi package above is just an example. Please use the latest exi prod release available.
| |
| − |
| |
| − | ==== 4. Reset the device: ====
| |
| − | reset
| |
| − |
| |
| − | The device should now be upgraded with the prod image.
| |
| | | | |
| | [[Category:Troubleshooting]] | | [[Category:Troubleshooting]] |
