Difference between revisions of "Turbine Image Recovery"
Jump to navigation
Jump to search
(→Using Static IP) |
|||
| (39 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
This article describes how to upload firmware to a Turbine device if the firmware is corrupted and the unit is bricked. | This article describes how to upload firmware to a Turbine device if the firmware is corrupted and the unit is bricked. | ||
| − | It is important that this must be used as a last resort and the only way to reach the unit is using serial port. | + | It is important that this must be used as a last resort and if the only way to reach the unit is using serial port. |
This applies to the following devices: | This applies to the following devices: | ||
| − | *ESC1 Controller - only the Secondary System Controller | + | * [[ESC1]] Controller - only the Secondary System Controller |
| − | *ENA Amplifiers | + | * [[:Category:Central_Equipment|ENA Amplifiers]] |
| − | *ECPIR-P/ECPIR-3P/EAPIR-8 Access Panels | + | * [[:Category:Indoor Access Panels|ECPIR-P/ECPIR-3P/EAPIR-8 Access Panels]] |
| − | *EAPII-1/EAPII-6 Access Panels | + | * [[:Category:Outdoor_Access_Panels|EAPII-1/EAPII-6 Access Panels]] |
| − | + | * [[:Category:Kits|TKIS-2/TKIE-1/TKIE-2 kits]] | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | * | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| + | == Upgrade Procedures == | ||
| + | A complete guide on recovery with the use of VS-Turbine.ImageUpgrade application can be found [https://wiki.zenitel.com/wiki/Turbine_Stations_-_Image_recovery '''here''']. | ||
[[Category:Troubleshooting]] | [[Category:Troubleshooting]] | ||
Latest revision as of 12:54, 17 December 2018
This article describes how to upload firmware to a Turbine device if the firmware is corrupted and the unit is bricked.
It is important that this must be used as a last resort and if the only way to reach the unit is using serial port.
This applies to the following devices:
- ESC1 Controller - only the Secondary System Controller
- ENA Amplifiers
- ECPIR-P/ECPIR-3P/EAPIR-8 Access Panels
- EAPII-1/EAPII-6 Access Panels
- TKIS-2/TKIE-1/TKIE-2 kits
Upgrade Procedures
A complete guide on recovery with the use of VS-Turbine.ImageUpgrade application can be found here.
