Difference between revisions of "Release Note Exigo 1.6"

From exigoWiki
Jump to navigation Jump to search
(→‎MTN-2936 Missing device report can be sent as SNMP trap)
(→‎MTN-3041 EMT: Global snmp fixes)
Line 71: Line 71:
 
Two issues fixed:
 
Two issues fixed:
  
−
1. Bad indication for global snmp settings on device when selecting global.
+
# Bad indication for global snmp settings on device when selecting global.
−
2. During project reload, devices were not loading snmp settings properly when configured to global.
+
# During project reload, devices were not loading snmp settings properly when configured to global.
  
 
====MTN-2936 Missing device report can be sent as SNMP trap====
 
====MTN-2936 Missing device report can be sent as SNMP trap====

Revision as of 13:55, 9 May 2022

Contents

Exigo 1.6.3.1

Release status: Official, available
Release date: 26.04.2022
Software collection file: EXIGO-1.6.3.1.zip

Software included in EXIGO-1.6.3.1.zip

Product Version Product description
VSF-Turbine VSFT-PA.6.5.3.3 Firmware for the following devices: ESC1 (Secondary System Controller), ENA2100, ENA2200 AC2, ENA2400 AC2, ECPIR-3P, ECPIR-P, EAPIR-8, EAPFX-1, EAPFX-6, EAPII-1, EAPII-6, TKIS-2, TKIE-2, IP-LCM.
AlphaSys Firmware 13.0.3.15 Firmware for the ESC1 (Primary System Controller/AMC-IP board) alpha-sys_13.0.3.15.apkg, bsp_32.2.3.6.apkg
VS-EMT Exigo Management Tools EMT-1.7.3.1 Configuration tool, installed on a Windows PC
VS-DEVICE-MIB 201806190000Z SNMP MIB for Exigo EXI-Devices, for upload in 3rd-party SNMP based monitoring tools


Bugfixes and improvements

MTN-3784 Increased timeout for backed up amplifiers detect

Backup amplifier will wait longer after boot for backed up amplifiers to get ready to compensate for network equipment slow startup times.

MTN-3767 EMT: Control backup amplifiers

Take over and release amplifier options for ENA2200-AC2 and ENA2400-AC2 are now available.

MTN-3720 EMT Monitoring: Destinations in Audio Activity

Previously, only zones were available as destination for Audio Activity. Now, same destinations as for controller (ESC) are available in EMT Monitoring.

MTN-3702 EMT: Copy to paired device now works

Copy to paired device in EMT did not include all settings. This is now fixed.

MTN-3665 EMT: Added scrollbar to AVC section (Zone Editor) and Device Configuration List

MTN-3626 Kit devices will now read their IP address

MTN-3612 EMT Monitoring: Queue in Audio Activity monitoring

Queued call activity was not always appearing in monitoring list. Solved.

MTN-3608 EMT: IP-LCM Control Input Monitoring removal

IP-LCM is not capable of monitoring control inputs. Selection removed in EMT.

MTN-3522 EMT: IP-LCM inherit in A/B System

IP-LCM B not inheriting when configured to inherit. Now working.

MTN-3507 Control inputs on IP-LCM, Kits and Amplifiers now de-escalate correctly after escalated recall

MTN-3474 EMT: Delay for missing device possible to set on flowire

Flowires were not included when setting global delay time for missing device registration. Now working, and delay option can be set on each flowire individually.

MTN-3468 EMT Monitoring: Showing fault list on first connect

On first connect, EMT did not always bring up the fault list. Working fine now.

MTN-3218 EMT: Alarm with frequencies that are not within 50Hz to 4kHz range can not be verified

MTN-3041 EMT: Global snmp fixes

Two issues fixed:

  1. Bad indication for global snmp settings on device when selecting global.
  2. During project reload, devices were not loading snmp settings properly when configured to global.

MTN-2936 Missing device report can be sent as SNMP trap

System controller can send missing device report or PSC down as SNMP trap.

SNMP trap, Missing Device

Added snmp trap "Missing Device" for ESC1.

MTN-1956 External fault on panel

When multiple buttons were configured with same external fault ID, and user pressed off one of the buttons, system turned off all alarm LEDs with same fault ID even with other buttons active. Now working as it should.

MTN-1919 Fault LED will no longer stay lit after LED/system testing

EPB-492 EMT: Corrected resolution of delay on output from 10 ms to 20 ms

EPB-484 SLM audio level values are now reported correctly

EPB-470 GPO's can now be tested from IP-LCM's webpage

EPB-452 CO - fault indication on unacknowledged fault

From EMT, user may activate GPO to trigger only at unacknowledged faults in the fault state selection.

Known Issues

MTN-3565 When booting up an AB system, the controller comes up with "buzzer active" with no faults

This happens on the A controller. Click the wheel to silence the "buzzer".

Exigo 1.5.3.0

Release status: Official, available
Release date: 24.11.2021
Software collection file: EXIGO-1.5.3.0.zip

Software included in EXIGO-1.5.3.0.zip

Product Version Product description
VSF-Turbine VSFT-PA.6.3.3.0 Firmware for the following devices: ESC1 (Secondary System Controller), ENA2100, ENA2200 AC2, ENA2400 AC2, ECPIR-3P, ECPIR-P, EAPIR-8, EAPFX-1, EAPFX-6, EAPII-1, EAPII-6, TKIS-2, TKIE-2, IP-LCM.
AlphaSys Firmware 13.0.3.13 Firmware for the ESC1 (Primary System Controller/AMC-IP board) alpha-sys_13.0.3.13.apkg, bsp_32.2.3.6.apkg
VS-EMT Exigo Management Tools EMT-1.6.3.0 Configuration tool, installed on a Windows PC
VS-DEVICE-MIB 201806190000Z SNMP MIB for Exigo EXI-Devices, for upload in 3rd-party SNMP based monitoring tools


New Features and Enhancements

EPB-303 ENA2x00 AC2 released

From Exigo 1.5.3.0 version the ENA2x00 AC2 are supported. To learn more about the new amplifiers please go to https://www.zenitel.com/product. Please note that ENA2x00 AC2 are not yet supported in SIP and ICX AlphaCom mode.

Bugfixes and improvements

MTN-3539 SNMP temperature is now displayed correctly

MTN-3467 Global system settings override device settings

Notification is added to system settings page to warn user that saving system settings overrides local settings.

MTN-2266 Refresh issue related to tick tone fixed

When a tick tone was started from amplifier web, the button label was not refreshed when another activity stopped the tick tone. The web indicated that tick tone was still active. This is now fixed.

MTN-2172 Tick tone will now be played out on access panels which is part of a zone

Known Issues

MTN-3565 When booting up an AB system, the controller comes up with "buzzer active" with no faults

This happens on the A controller. Click the wheel to silence the "buzzer".

Retrieved from "https://exigo.zenitel.com/w/index.php?title=Release_Note_Exigo_1.6&oldid=17768"