Difference between revisions of "Factory Default"
| Line 10: | Line 10: | ||
In the web browser go to '''System Maintenance''' -> '''System Recovery''' | In the web browser go to '''System Maintenance''' -> '''System Recovery''' | ||
| − | [[File:Factory default 1.JPG|thumb|left|500px|AMC-IP - Factory Default]] | + | [[File:Factory default 1.JPG|thumb|left|500px|AMC-IP web interface - Factory Default]] |
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
| Line 21: | Line 21: | ||
In the web browser go to '''Station Administration''' -> '''Reboot''' | In the web browser go to '''Station Administration''' -> '''Reboot''' | ||
| − | [[File:Factory default 2.JPG|thumb|left|500px|Secondary System Controller - Factory Default]] | + | [[File:Factory default 2.JPG|thumb|left|500px|Secondary System Controller web interface - Factory Default]] |
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
| Line 38: | Line 38: | ||
In the web browser go to '''Station Administration''' -> '''Reboot''' | In the web browser go to '''Station Administration''' -> '''Reboot''' | ||
| − | [[File:Factory default 2.JPG|thumb|left|500px|ENA Amplifier - Factory Default]] | + | [[File:Factory default 2.JPG|thumb|left|500px|ENA Amplifier web interface - Factory Default]] |
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
| Line 50: | Line 50: | ||
[[File:Factory default 4.png|thumb|left|500px|ENA - GUI]] | [[File:Factory default 4.png|thumb|left|500px|ENA - GUI]] | ||
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
| + | |||
| + | == Factory Default on Access Panels == | ||
| + | |||
| + | To an access panel to factory default: | ||
| + | In the web browser go to '''Station Administration''' -> '''Reboot''' | ||
| + | |||
| + | [[File:Factory default 2.JPG|thumb|left|500px|Access Panel web interface - Factory Default]] | ||
| + | <br style="clear:both;" /> | ||
| + | |||
[[Category:Troubleshooting]] | [[Category:Troubleshooting]] | ||
Revision as of 07:10, 25 October 2016
This article describes how to set the different Exigo devices back to factory default.
If you encounter problems with a system a factory default might help solving the problem.
Contents
Factory Default on ESC-1 System Controller
The ESC-1 consists of Primary System Controller and Secondary System Controller.
Primary System Controller
To set the Primary System Controller (AMC-IP board) to factory default: In the web browser go to System Maintenance -> System Recovery
There is two ways to do a factory default:
- Load Factory Defaults - This resets the configuration data. IP settings are kept.
- Clean & Factory Default - This resets the configuration data. It also remove license, SysLog and Backup files. Removes Exigo mode. IP settings are kept.
Secondary System Controller
To set the Secondary System Controller to factory default: In the web browser go to Station Administration -> Reboot
There is two ways to do a factory default:
- Factory Reset - This resets the configuration data. The SSC gets default IP address (169.254.1.100).
- Factory Reset with DHCP - This resets the configuration data. The SSC is set to receive IP from DHCP.
It is also possible to do a Factory default from the GUI on the controller.
In the GUI go to Service -> Restart & Restore
Factory Default on ENA Amplifier
To set a ENA amplifier in factory default: In the web browser go to Station Administration -> Reboot
There is two ways to do a factory default:
- Factory Reset - This resets the configuration data. The ENA gets default IP address (169.254.1.100).
- Factory Reset with DHCP - This resets the configuration data. The ENA is set to receive IP from DHCP.
It is also possible to do a Factory default from the GUI on the controller.
In the GUI go to Service -> Restart & Restore
Factory Default on Access Panels
To an access panel to factory default: In the web browser go to Station Administration -> Reboot
