Difference between revisions of "Factory Default"
(→Factory Default on Flowire) |
(→Factory Default on Flowire) |
||
| Line 71: | Line 71: | ||
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
{| border="1" | {| border="1" | ||
| − | | align="center" style="background:#ffcb00;" width="50pt"| 1 || align="left" | ''' | + | | align="center" style="background:#ffcb00;" width="50pt"| 1 || align="left" | '''Password Reset Button''' || align="left"| Pressing and holding this button for more than 15 seconds will reset the NMK password to the default: '''HomePlugAV0123''' |
|- | |- | ||
| align="center" style="background:#ffcb00;" width="50pt"| 2 || align="left" | Ethernet connection || align="left"| Ethernet connection without power | | align="center" style="background:#ffcb00;" width="50pt"| 2 || align="left" | Ethernet connection || align="left"| Ethernet connection without power | ||
| Line 81: | Line 81: | ||
|} | |} | ||
<br> | <br> | ||
| − | + | In addition to reseting the NMK password to its default, the procedure will | |
| − | + | also set the following factory defaults: | |
| − | + | * DHCP will be turned on | |
| − | + | * IGMP snooping querier will be turned on | |
[[Category:Troubleshooting]] | [[Category:Troubleshooting]] | ||
Revision as of 12:14, 2 November 2016
This article describes how to set the different Exigo devices back to factory default.
If you encounter problems with a system a factory default might help solving the problem.
Contents
Factory Default on ESC-1 System Controller
The ESC-1 consists of Primary System Controller and Secondary System Controller.
Primary System Controller
To set the Primary System Controller (AMC-IP board) to factory default:
In the web browser go to System Maintenance -> System Recovery
There is two ways to do a factory default:
- Load Factory Defaults - This resets the configuration data. IP settings are kept.
- Clean & Factory Default - This resets the configuration data. It also remove license, SysLog and Backup files. Removes Exigo mode. IP settings are kept.
Secondary System Controller
To set the Secondary System Controller to factory default:
In the web browser go to Station Administration -> Reboot
There is two ways to do a factory default:
- Factory Reset - This resets the configuration data. The SSC gets default IP address (169.254.1.100).
- Factory Reset with DHCP - This resets the configuration data. The SSC is set to receive IP from DHCP.
It is also possible to do a Factory default from the GUI on the controller.
In the GUI go to Service -> Restart & Restore
Factory Default from the GUI will not restart the applications responsible for audio and monitoring (EdgeAudioClient & SysMon).
Because of this it is recommended to do factory default from the web if possible.
Factory Default on ENA Amplifier
To set a ENA amplifier in factory default:
In the web browser go to Station Administration -> Reboot
There is two ways to do a factory default:
- Factory Reset - This resets the configuration data. The ENA gets default IP address (169.254.1.100).
- Factory Reset with DHCP - This resets the configuration data. The ENA is set to receive IP from DHCP.
It is also possible to do a Factory default from the GUI on the controller.
In the GUI go to Service -> Restart & Restore
Factory Default from the GUI will not restart the applications responsible for audio and monitoring (EdgeAudioClient & SysMon).
Because of this it is recommended to do factory default from the web if possible.
Factory Default on Access Panels
To an access panel to factory default:
In the web browser go to Station Administration -> Reboot
Factory Default on Flowire
To reset a Flowire unit use the Restore button (1):
| 1 | Password Reset Button | Pressing and holding this button for more than 15 seconds will reset the NMK password to the default: HomePlugAV0123 |
| 2 | Ethernet connection | Ethernet connection without power |
| 3 | Alt. position for DIN clips | |
| 4 | DIN mounting clips | Plastic clip to mount the Flowire Converter box to a DIN rail |
In addition to reseting the NMK password to its default, the procedure will
also set the following factory defaults:
- DHCP will be turned on
- IGMP snooping querier will be turned on
