Difference between revisions of "Firewall Settings"
(→Firewall Settings) |
|||
| (15 intermediate revisions by 2 users not shown) | |||
| Line 3: | Line 3: | ||
This article describes the firewall/filter settings needed for the Exigo System.<br> | This article describes the firewall/filter settings needed for the Exigo System.<br> | ||
There might be different needs for different system setups.<br> | There might be different needs for different system setups.<br> | ||
| − | + | These settings are the minimum required to get the system to work. | |
== Firewall Settings == | == Firewall Settings == | ||
| − | On the [[AMC-IP|Primary System Controller]] ([[AMC-IP]] board) the minimum filters | + | On the [[AMC-IP|Primary System Controller]] ([[AMC-IP]] board) the minimum filters have to be enabled for '''Eth1''': |
{| class="wikitable" | {| class="wikitable" | ||
| − | ! style="text-align:left;"| | + | ! style="text-align:left;" | Protocol |
! Port | ! Port | ||
|- | |- | ||
| Line 30: | Line 30: | ||
For AlphaCom/SIP integration: | For AlphaCom/SIP integration: | ||
{| class="wikitable" | {| class="wikitable" | ||
| − | ! style="text-align:left;"| | + | ! style="text-align:left;" | Protocol |
! Port | ! Port | ||
|- | |- | ||
| Line 37: | Line 37: | ||
|} | |} | ||
| + | Adjusting firewall settings for the Primary System Controller is done in EMT: | ||
| + | * Go to '''System''' > '''Default Firewall Setting''' | ||
| + | [[File:Firewall 3.JPG|thumb|left|500px|EMT - Default Firewall Setting]] | ||
| + | <br style="clear:both;" /> | ||
| + | == Setup Wizard == | ||
| + | During the creation of a new database it is possible to open up for SNMP traffic in the system. | ||
| + | [[File:Firewall 2.JPG|thumb|left|500px|Setup wizard - SNMP]] | ||
| + | <br style="clear:both;" /> | ||
| + | Enabling SNMP can be done on the last page of the wizard. | ||
| + | == Default Firewall Setting == | ||
| + | The default firewall settings for all endpoints can be changed in EMT.<br> | ||
| + | * Go to '''System''' > '''Default Firewall Setting''' | ||
| + | [[File:Firewall 3.JPG|thumb|left|500px|Default Firewall Setting]] | ||
| + | <br style="clear:both;" /> | ||
| + | Select the desired firewall/port. <br> | ||
| + | This settings will then be the default for all devices. | ||
| + | |||
| + | === VoIP ports === | ||
| + | By default the number of VoIP ports is set to 61000:61150. <br> | ||
| + | In some rare cases this may be insufficient. <br> | ||
| + | For more information see [[VoIP ports|'''this''']] article. | ||
| + | |||
| + | == Individual Settings == | ||
| + | It is possible to set individual firewall settings for each device (not recommended).<br> | ||
| + | * In the device tree go to the desired '''Device''' > '''Network Interface''' > '''Firewall''' | ||
| + | [[File:Firewall 4.JPG|thumb|left|500px|Individual Firewall Setting]] | ||
| + | <br style="clear:both;" /> | ||
| + | To change firewall settings:<br> | ||
| + | * Select the desired firewall/port and uncheck the '''Use System Setting''' checkbox | ||
[[Category:Troubleshooting]] | [[Category:Troubleshooting]] | ||
[[Category:Getting started]] | [[Category:Getting started]] | ||
Latest revision as of 13:06, 16 November 2017
This article describes the firewall/filter settings needed for the Exigo System.
There might be different needs for different system setups.
These settings are the minimum required to get the system to work.
Contents
Firewall Settings
On the Primary System Controller (AMC-IP board) the minimum filters have to be enabled for Eth1:
| Protocol | Port |
|---|---|
| ZAP (Zenitel Application Protocol) | TCP-50004 |
| NTP server | UDP-123 |
| VoIP Audio | UDP-61000:61150 |
| IP Stations | TCP-50001 |
| HTTP | TCP-80 |
For AlphaCom/SIP integration:
| Protocol | Port |
|---|---|
| SIP | UDP-5060 |
Adjusting firewall settings for the Primary System Controller is done in EMT:
- Go to System > Default Firewall Setting
Setup Wizard
During the creation of a new database it is possible to open up for SNMP traffic in the system.
Enabling SNMP can be done on the last page of the wizard.
Default Firewall Setting
The default firewall settings for all endpoints can be changed in EMT.
- Go to System > Default Firewall Setting
Select the desired firewall/port.
This settings will then be the default for all devices.
VoIP ports
By default the number of VoIP ports is set to 61000:61150.
In some rare cases this may be insufficient.
For more information see this article.
Individual Settings
It is possible to set individual firewall settings for each device (not recommended).
- In the device tree go to the desired Device > Network Interface > Firewall
To change firewall settings:
- Select the desired firewall/port and uncheck the Use System Setting checkbox
