Difference between revisions of "ENA2100-AC One Channel Mode"
(→Configuration) |
|||
| (11 intermediate revisions by the same user not shown) | |||
| Line 7: | Line 7: | ||
One Channel Mode is configured in [[EMT overview|EMT]]. <br> | One Channel Mode is configured in [[EMT overview|EMT]]. <br> | ||
Go to '''System''' -> '''ENA2100''' -> '''Audio Line'''. | Go to '''System''' -> '''ENA2100''' -> '''Audio Line'''. | ||
| − | [[File:ENA2100 one channel mode 1.png|left| | + | [[File:ENA2100 one channel mode 1.png|thumb|left|600px|ENA2100-AC One Channel Mode]] |
| + | <br style="clear:both;" /> | ||
| + | |||
| + | == Status LED == | ||
| + | There is a green LED inside the Amplifier, right behind the loudspeaker connector, which will turn ON when "One Channel mode" is active. <br> | ||
| + | The LED can be seen through the rear grille. | ||
| + | |||
| + | [[File:ENA2100 one channel mode 2.jpg|thumb|left|400px|One Channel Mode LED indication]] | ||
| + | <br style="clear:both;" /> | ||
| + | It is recommended to check that the "One Channel LED" is turned '''ON''' before bridging the two channels. | ||
| + | |||
| + | == Wiring == | ||
| + | The bridging the two loudspeaker channels into one must be done by the installer, by shorting wires on the rear connector, or at external terminal blocks. | ||
| + | |||
| + | In case of '''100V line''': | ||
| + | * Short "Com"-terminal for Ch1 to "Com"-terminal for Ch2. | ||
| + | * Short "100V"-terminal for Ch1 to "100V"-terminal for Ch2. | ||
| + | |||
| + | In case of '''70V line''': | ||
| + | |||
| + | * Short "Com"-terminal for Ch1 to "Com"-terminal for Ch2. | ||
| + | * Short "70V"-terminal for Ch1 to "70V"-terminal for Ch2. | ||
| + | |||
| + | [[File:ENA2100 one channel mode 3.jpg|thumb|left|400px|ENA2100 - bridging]] | ||
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
Latest revision as of 11:58, 10 January 2019
The ENA2100-AC Amplifier supports One Channel Mode.
When "One Channel mode" is activated, the two loudspeaker channels will play identical audio, and the audio will be in phase.
One can then choose to use two separate loudspeaker loops, each with maximum 100W, or one can bridge the two output channels, and use one loudspeaker loop with up to 200W load.
Configuration
One Channel Mode is configured in EMT.
Go to System -> ENA2100 -> Audio Line.
Status LED
There is a green LED inside the Amplifier, right behind the loudspeaker connector, which will turn ON when "One Channel mode" is active.
The LED can be seen through the rear grille.
It is recommended to check that the "One Channel LED" is turned ON before bridging the two channels.
Wiring
The bridging the two loudspeaker channels into one must be done by the installer, by shorting wires on the rear connector, or at external terminal blocks.
In case of 100V line:
- Short "Com"-terminal for Ch1 to "Com"-terminal for Ch2.
- Short "100V"-terminal for Ch1 to "100V"-terminal for Ch2.
In case of 70V line:
- Short "Com"-terminal for Ch1 to "Com"-terminal for Ch2.
- Short "70V"-terminal for Ch1 to "70V"-terminal for Ch2.
Availability
This function is available from Exigo 1.4 and later.
