Secondary System Controller Update

System Controller Simplified Block Diagram

The Exigo System Controller consist of two main components:

• Primary System Controller, PSC
• Secondary System Controller, SSC

This article describes how to upgrade the software on the Secondary System Controller part of the Exigo System Controller. The Secondary System Controller is also called Turbine Board.

Upgrade using the Web Interface

Attention

When flashing new image (exi-4.2.2.3 or newer) for the first time the bootloader must be updated first.
This is done by entering boot/<image_name> (boot/exi-n.n.n.n) in web upgrade image file field before upgrading image.
To do a "clean" upgrade use exi image with switch: all/<image_name> (all/exi-n.n.n.n)

Prerequisites

1. A TFTP Server must be available. A TFTP server can be downloaded from here: http://tftpd32.jounin.net/tftpd32_download.html
2. Download the latest Exigo firmware/software package and unzip the folder.
3. Check if your local firewall is not blocking incoming ping/ICMP (Turbine station is pinging TFTP Server during update process).

Upgrade procedure

• Start the TFTP server program and click Browse, and select the folder where the latest version of exi-x.x.x.x software files are located

TFTP32

• Log on to the Secondary System Controller web interface. Default login credentials are admin and alphaadmin. Select Station Administration > Manual Upgrade
• Enter the IP address of the TFTP server (I.e. the IP address of your PC)
• Enter the image file: exi-x.x.x.x, and click Save settings

Secondary System Controller - Upgrade web interface

The station will now contact the TFTP server and download the files. The upgrade procedure takes about 3 minutes. The process can be monitored by clicking the Log viewer tab in the TFTP server program.

Description of the exi-n.n.n.n package

This software package is valid for following products "NAME(devicetree)":

• ENA2200(ena2)
• ENA2400(ena2)
• ESC1(esc)
• EAPIR-8(extended-exigopanel)
• ECPIR-3P(extended-exigopanel)
• ECPIR-P(extended-exigopanel)
• EAPFX-1(ex)
• EAPFX-6(ex)
• EAPII-1(extended-industrial)
• EAPII-6(extended-industrial)
• TKIS-2(compact)

Alternative ways of upgrade

Alternative 1: upgrade only devtree & bootloader:

Set image file to "devtreeboot/exi-x-x-x-x"

Alternative 2: upgrade only devtree

• Set image file to "compact/exi-x-x-x-x"
• Set image file to "extended/exi-x-x-x-x"
• Set image file to "extended-industrial/exi-x-x-x-x"
• Set image file to "extended-exigopanel/exi-x-x-x-x"
• Set image file to "ex/exi-x-x-x-x"
• Set image file to "ena2/exi-x-x-x-x"
• Set image file to "esc1/exi-x-x-x-x"

Alternative 3: upgrade only bootloader

Set image file to "boot/exi-x-x-x-x"

Additional Information

Installing a TFTP server on your PC

• Download the TFTP Server program tftpd64 standard edition (installer) from http://tftpd32.jounin.net/tftpd32_download.html.
• For 32 bit computers download tftpd32 standard edition (installer)
• Unzip the tftpdxx.yyy.zip file. (e.g. to C: \tftpdxx\)
• Run the tftpdxx.exe file. The program is run by selecting the extracted .exe file, no installation is needed.
• Turn off every thing except "TFTP Server" under Settings > Global. Escpecially important to turn off "DHCP Server", as this server part of the tftpxx application may interfere with other DHCP servers in the network
• Select the base directory (e.g. C:\Software) by selecting the Settings > TFTP, then Browse
• The TFTP Server program must be running during the software upgrade process

Troubleshooting

In the case the upgrade is not successful it may be due to a windows setting.

• For Windows XP: http://www.sysprobs.com/enable-ping-in-xp
• For Windows7: http://www.sysprobs.com/enable-ping-reply-windows-7
• For Windows10: http://www.sysprobs.com/enable-ping-reply-and-ftp-traffic-in-windows-10-and-server