ENA2100-AC

ENA2100-AC

Exigo Network Amplifier

• 2 x 100 watt continuous GA effect
• Power efficient class D technology
• 115/230 VAC power
• Redundant Ethernet connections
• Digital audio processing
• Loudspeaker line monitoring
• Line input
• Embedded tick tone generator
• 2 configurable control outputs (24 VDC ±10%, 200 mA, monitored)
• 2 configurable control inputs

The Exigo Network Amplifier is designed for use in marine, offshore and other demanding environments. The amplifier utilizes state-of-the-art class D amplifier technology to ensure high power efficiency and superb audio quality for two audio channels which can be loaded with up to 100W each.

The Exigo Network Amplifier is part of the Exigo PA/GA system, which is based on standard Ethernet network and digital processing. Each amplifier has two network connections, allowing for redundant cabling between the amplifier and the network.
Using standard network equipment also allows for a much wider selection of standard network equipment. The amplifier is also compatible with the Alphacom platform, allowing for advanced communication systems with both intercoms and PA.

The complete amplifier is self-monitoring and this includes advanced monitoring of the speaker lines and internal system. The audio output channels can be monitored for line faults such as shorts, ground faults and large load changes.
In addition, up to 10 intelligent Line End Transponders (ELTSI) can be placed on the speaker lines for additional accuracy in the line monitoring. The amplifier also monitors control inputs, power supplies, temperature, network connections and every other components required for operation of essential services. Faults will be reported to the system controller, but will also be indicated locally on the amplifier.

The amplifier’s configurable control inputs/outputs and audio inputs can be used to trigger various activities in the system.
The audio line input can also be configured in a "hardware bypass" mode where audio on the line input will be forwarded to the 100V channels directly, even when no server is available. This allows for additional redundancy and functions to be built around this amplifier.

 The ENA2100-AC cannot be used as a backup amplifier.

Installation

Overview - Front

1	Mounting Flanges	The mounting flanges are used to mount the unit in 19” equipment racks with 2HU in double configuration.
2	Ventilation Inlets	The ventilation inlets should be kept free of obstacles and dust. Fans control the airflow based on internal temperature.
3	Status Indicators	The status indicators are used to display the status of important parameters like power supply and faults. There is also a VU indicator for channel 1 and channel 2.

---

Overview - Back

1	Ethernet Ports	Redundant Ethernet connections for audio and control data.
2	Audio Input	Line-in audio input for external audio sources.
3	Control Inputs	2 configurable control inputs. Each input is activated by closing the loop between the two terminals.
4	Control Outputs	2 configurable control outputs. Each is made of a 24VDC signal. The 24VDC can source max 200mA and has overcurrent protection.
5	Fault Relay Output	A switching relay (NO, NC & COM) kept in the active position between COM and NO as long as no faults are present in the device.
6	Speaker Outputs	100 and 70 volts outputs per channel.
7	Factory Reset Button	To reset the amplifier to factory default settings: Insert a straightened paper clip or similar device into the hole - Wait 7 seconds after power-on, then push for 1 second and release.
8	AC Power Switch	Power switch for AC power.
9	AC Power Inlet	AC power inlet for 110 to 230 VAC. The power inlet has a V-Lock mechanism for a secure connection.
10	Ground Connection	Ground connection for grounding of the unit. This is connected in parallel with the ground connection in the AC power inlet.

---

Status LEDs

The ENA2100-AC Amplifier has status LED indicators in the front panel:

ENA2100 Status LEDs

• Power: Steady green light when the amplifier is powered on.
• Status: When the amplifier is operational, the LED is flashing green. The LED will be steady lit during the startup sequence.
• Fault: The Yellow fault LED will be lit whenever the amplifier detects an error. Which errors to report is configurable. The Fault LED is lit during the startup sequence.
• Disabled: This Yellow LED will be lit if the loudspeaker output channels are disabled.
• VU 1: This Green and Red LED is lit when there is audio activity on loudspeaker channel 1.
• VU 2: This Green and Red LED is lit when there is audio activity on loudspeaker channel 2.

One Channel Mode - Bridging

Information on configuration of One Channel Mode can be found here.

Dimensions

Accessories

ELTSI-1	ENA2100-AC Double mounting	ENA2100-AC Single mounting

Additional Documentation

For more documentation, please visit the Zenitel web page: https://www.zenitel.com/product/ena2100-ac