TKIE-1

TKIE-1

Voip Intercom Module

The TKIE-1 is the extended version of our Turbine Kit range. It offers the same high quality audio as the TKIS-x kit, but adds to the feature list with an extra RJ45 port for dual Ethernet connectivity, dual relays, and a header for easy connection of audio accessories. For high-power applications, the TKIE-1 may be complemented with the TA-10 Relay Module which offers 2 DPDT relays suited for high-voltage/high-current applications.

• IP station kit with extended functionality
• Dual RJ45 for Ethernet connectivity (with switch)
• Dual relays (DPDT)
• 6 configurable I/Os (input, output or LED-driving)
• Line-in/Line-out connectivity for connection to audio devices
• Header for connecting audio accessories
• Possibility for connecting high-power relay module (TA-10)
• High quality Turbine™ class output with 10W amplifier
• Full open duplex and digital noise reduction

Connections

There are two RJ-45 ports located on the TKIE-1 that are used for PoE/LAN Ethernet connection.

There are 6 I/O connection options for the TKIE-1. These connections are used as digital input (eg. form a closing contact), digital output (5V), or LED driving (20mA max) for connecting sensors, indicators or integration to other systems.

Ethernet/Power	The TKIE-1 supports Power over Ethernet (PoE, IEEE 802.3 a-f) where power can be drawn from either the spare line or signal line.*
Secondary Power	If PoE in not available, the TKIE-1 can be powered from a 24-48 VDC local power supply.**
Relays	There are two Double Throw relay contacts with 60W switching power. COM, NO, NC contacts are provided.
Input/Output	6 I/Os are available. Each I/O can be configured as either input, output, or LED driver.
Audio Line Out	A balanced 600 ohm audio line out with induction loop signal

 Use cables crimped with ferrules for terminal block connectors

*If connected to two PoE-capable switches, only one of the ports will negotiate PoE; hence this is not a good solution for 
power redundancy (switch failure might lead to a reboot). Instead a “dumb” PoE injector (spare-pair power) should be used 
for the two Ethernet ports or a local 24 VDC local power backup. 

**If used together with PoE the station can be powered by 24 VDC as a local power backup.

• When the TKIE-1 is connected to the network, its IP address is automatically obtained from a DHCP server or an IP address in the range 169.254.x.x will be assigned.

P1&P2 RJ45 PoE port for 10/100 Mbit Ethernet connection.

The station can be powered from this port if the line supports Power over Ethernet (PoE).

RJ45 PoE port

P3 Secondary Power; 24-48VDC

P4 10-pin plug-on terminal for external connections.

Pin 1 5.3V

Pin 2 GND

Pin 3 Button Input or LED Driver

Pin 4 Button Input or LED Driver

Pin 5 Button Input or LED Driver

Pin 6 Button Input or LED Driver

Pin 7 Button Input or LED Driver

Pin 8 Button Input or LED Driver

Pin 9 600 ohm balanced line out +

Pin 10 600 ohm balanced line out -1

P5 6-pin plug-on terminal for external connections.

Pin 1 COM relay 1

Pin 2 NO relay 1

Pin 3 NC relay 1

Pin 4 COM relay 2

Pin 5 NO relay 2

Pin 6 NC relay 2

 Relay 1 is configured as output 7, and Relay 2 is configured as output 8!

P6 Loudspeaker & Electret microphone

Pin 1 10W Speaker amplifier +

Pin 2 10W Speaker amplifier -

Pin 3 Electret Microphone +

Pin 4 Electret Microphone -

J2 Turbine Relay Module - TA-10

 Relay 3 is configured as output 9, and Relay 4 is configured as output 10!

J8 Headset/Handset connector

Pin 1 Offhook

Pin 2 GND

Pin 3 PTT

Pin 4 Handset Mic Positive

Pin 5 Handset Mic Negative

Pin 6 Headphone Positive

Pin 7 Headphone Negative

Pin 8 Line In Positive

Pin 9 Line In Negative

Restore Factory Defaults

See article: Restore Factory Default

Accessories

TA-10

Additional Documentation

For more documentation, please visit the Zenitel web page: https://www.zenitel.com/product/tkie-1

Availability

This device is supported from Exigo 1.3 and newer.