Difference between revisions of "Setting up a small system"
| Line 27: | Line 27: | ||
|011010 | |011010 | ||
|} | |} | ||
| − | |||
| Line 41: | Line 40: | ||
<br style="clear:both;" /> | <br style="clear:both;" /> | ||
* Enter the appropriate IP address (10.1.10.21) in the '''npe_eth1''' field | * Enter the appropriate IP address (10.1.10.21) in the '''npe_eth1''' field | ||
| + | |||
==Step 3: Secondary System Controller Setup== | ==Step 3: Secondary System Controller Setup== | ||
| Line 64: | Line 64: | ||
** IP-address: '''10.1.0.20''' | ** IP-address: '''10.1.0.20''' | ||
** Subnet-mask: '''255.255.255.0''' | ** Subnet-mask: '''255.255.255.0''' | ||
| + | |||
==Step 3: ENA Amplifier Setup== | ==Step 3: ENA Amplifier Setup== | ||
| Line 87: | Line 88: | ||
** IP-address: '''10.1.0.30''' | ** IP-address: '''10.1.0.30''' | ||
** Subnet-mask: '''255.255.255.0''' | ** Subnet-mask: '''255.255.255.0''' | ||
| + | |||
| + | |||
| + | ==Step 3: ECPIR-3P Setup== | ||
[[Category:How-To]] | [[Category:How-To]] | ||
Revision as of 11:55, 21 June 2016
This page will explain how to configure and test a small Exigo system.
Contents
Step 1: IP addresse
Each device will need to be configured with an IP address and subnet which is in range of the AMC-IP card.
Table below lists IP range for a small system with one amplifier and on access panel. All subnets are set to 255.255.255.0
| Device | IP | Dirctory number |
|---|---|---|
| PSC | 10.1.0.21 | |
| ESC-1 | 10.1.0.20 | 013010 |
| ENA | 10.1.0.30 | 012010 |
| ECPIR-3P | 10.1.0.50 | 011010 |
Step 2: Primary System Controller Setup
Open up the front of the ESC1 Controller. Connect your computer to eth0.
- Open a web browser and enter the default IP address of port npe_eth0: 169.254.1.5
- Log in with username: admin and password: alphaadmin
- Select System Configuration > Interfaces
- Enter the appropriate IP address (10.1.10.21) in the npe_eth1 field
Step 3: Secondary System Controller Setup
Connect your computer to eth1 (on the back of the ESC1 Controller).
To find th IP adress of the Secondary System Controller:
- Turn the menu selection knob on the system controller to select Settings > Network to see the IP address on the display.
To configure the IP address and directory number:
- Open a web browser and enter IP address: 169.254.x.x
- Log in with username: admin and password: alphaadmin
- Select Station Main > Main Settings
Set the following values:
- Station Mode: Use Exigo
- Registration Settings:
- Primary System Controller address: 10.1.0.21 (IP address previously set for PSC)
- Directory Number: 013010 (corresponds to the Directory Number automatically assigned to the system controller in the Exigo Management Tool)
- IP Settings: Static IP
- IP-address: 10.1.0.20
- Subnet-mask: 255.255.255.0
Step 3: ENA Amplifier Setup
Connect your computer to eth1 (on the back of the ENA Amplifier).
To find th IP adress of the ENA Amplifier:
- Turn the menu selection knob on the Amplifier to select Settings > Network to see the IP address on the display.
To configure the IP address and directory number:
- Open a web browser and enter IP address: 169.254.x.x
- Log in with username: admin and password: alphaadmin
- Select Station Main > Main Settings
Set the following values:
- Station Mode: Use Exigo
- Registration Settings:
- Primary System Controller address: 10.1.0.21 (IP address previously set for PSC)
- Directory Number: 013010 (corresponds to the Directory Number automatically assigned to the system controller in the Exigo Management Tool)
- IP Settings: Static IP
- IP-address: 10.1.0.30
- Subnet-mask: 255.255.255.0
